NTT HEATING SDN BHD
  • Home
  • Corporate Profile
  • Gallery
  • Contact Us
NTT HEATING SDN BHD
Require Quote
Menu
NTT HEATING SDN BHD
Require Quote
PRODUCT CATEGORIES
  • Best Seller
  • Product
    Home Heating

    Home Heating

    Refrigerator Counter

    Refrigerator Counter

    Commercial Cooking

    Commercial Cooking

    Water Urn Heater

    Water Urn Heater

    NH Thermostat /RHEAT Temperature Controller

    NH Thermostat /RHEAT Temperature Controller

    Sauna/SPA /Pools

    Sauna/SPA /Pools

    HVAC/ Drying & Comfort Heating

    HVAC/ Drying & Comfort Heating

    Industrial / Oil & Gas

    Industrial / Oil & Gas

    Water / Oil Immersion Heating

    Water / Oil Immersion Heating

    Circulation Heater

    Circulation Heater

    Plastic / Packaging

    Plastic / Packaging

    NTT 11 Series

    NTT 11 Series

    NTT Thermocouple / Tassei Thermocouple Wire

    NTT Thermocouple / Tassei Thermocouple Wire

    Tassei Heat Resistance Cable

    Tassei Heat Resistance Cable

    Level Sensor

    Level Sensor

    Space Heating /Anti Condensation Heater

    Space Heating /Anti Condensation Heater

    Laundry/ Hot Air Open Coil Heating

    Laundry/ Hot Air Open Coil Heating

Click to enlarge
Home HVAC / Drying & Comfort Heating Ranco Auto Cut OFF
Pilot Indicator Light
Back to products
Rocker Switch (LS-006D Series)

Ranco Auto Cut OFF

General Description
The L Series, L7, LM7 and LM8, is a family of fixed setting temperature limit controls whose design is failsafe. The L7 is auto reset, whilst LM7 and LM8 are manual reset. The operating temperatures are factory set and non-adjustable by the customer. Settings are available between 50 and 160ºC with capillary length from 450-2000mm (1000mm standard). The L7/LM7 are SPST (single pole singlethrow) and LM8 is DPST (double pole single throw)

Features

  • Element
  • Auto or manual reset
  • Fail-safe (cut-out to safety)
  • 16(3)A 400V ~. For LM8 ratings apply to each pole
  • Variety of settings and capillary options
  • Narrow profile to fit applications where space is limited
  • Versions available for Class I and Class II appliances
  • Versions for millivolt circuits (L7/LM7 only) available
  • Simple mounting
Add to quote
This product is already in your quote request list.
Browse the list
Share:
  • Description
Description
Download Brochure

Applications
These controls are used on any application where protection against overheat is required. Typical applications are:-

  • ‘Boil dry’ protection for waterheaters, washing machines, dishwashers, vending machines (protection of heating elements)
  • High temperature cut-out on central heating boilers
  • Blocked flue sensor on boilers with natural draft (on operation the gas supply to the burner is switched off)
  • Protection against overheating in panel/convector heaters
  • Overheat safety for AC cassette units equipped with an electric boost heater
  • Overheat safety on compressor discharge pipes
Electrical Rating: L7/LM7: 16A 400V~resistive
3A 400V~inductive
LM8: ratings apply to each pole
Switch: SPST break on rise of temperature
DPST (LM8) break on rise of temperature
(note: for millivolt application L7/LM7 can be supplied with goldplated contacts)
Terminals: Tab 6,3mm
Terminal Configuration: As shown, earth terminals available if required
Approvals: Approved throughout Europe
Special versions approved for North America (see chart)
Maximum Head
Temperature:
At least 15ºC below sensed temperature, max 90ºC
Temperature Range:   Fixed settings between 50ºC and 160ºC to order (factory set)
Tolerances: Standard ±8ºK on models with-out temperature, 50 – 115ºC ±3ºK is available
Capillary Length: 450 and 2000mm(in accordance to customer specification)
Capillary Insulation: Available on request
Capillary Form: Straight or coiled (minimum diameter 6mm) Approximately 400mm of capillary or the complete sensing
element is required for optimum sensing
Cross Ambient: Cross ambient versions with solid bulbs are available (LM7 and LM8 only). Temperature range 50 – 130°C.
The following information should be supplied with every enquiry:

  • Application
  • Model L7, LM7 or LM8
  • Setting required
  • Capillary length and sensing element (for options see Fig.3)
  • Control switch temperature
  • Mounting requirement (for options see Fig.2)

Barometric Effect
The control is calibrated to cut-out within the specified tolerance at a barometric pressure of 760mm Hg. For pressure higher (or lower) than this add (or subtract) 1°C for every 25mm Hg change.

This control must be applied and installed in line with local approvals and practices. Suitable earthing must be made by
appliance manufacturer and installer.

Related products

Air Finned Heater

Add to quote
This product is already in your quote request list.
Browse the list

Air Duct Heater

Add to quote
This product is already in your quote request list.
Browse the list

NTT Custom Made Duct Heater

Add to quote
This product is already in your quote request list.
Browse the list

HUBA Air Flow Switch

Add to quote
This product is already in your quote request list.
Browse the list

W-5 Series Thyristor

Add to quote
This product is already in your quote request list.
Browse the list
2022 ALL RIGHT RESERVED. NTT HEATING SDN BHD .
  • Menu
  • Categories
  • Best Seller
  • Circulation Heater
  • Commercial Cooking
  • Home Heating
  • HVAC / Drying & Comfort Heating
  • Industrial / Oil & Gas
  • Laundry/ Hot Air Open Coil Heating
  • Level Sensor
  • Temperature Controller
  • NTT 11 Series
  • NTT Thermocouple / Tassei Thermocouple Wire
  • Plastic / Packaging
  • Refrigerator Counter
  • Sauna / SPA / Pools
  • Space Heating /Anti Condensation Heater
  • Tassei Heat Resistance Cable
  • Water / Oil Immersion Heating
  • Water Urn heater
  • Products
  • Home
  • Corporate Profile
  • Gallery
  • Contact Us